2736-20 vs FX7211-Z
The 2736-20 beside the FLEX FX7211-Z, row by row. Both are jobsite table saws with the same blade diameter: blade diameter 8-1/4 in on the FX7211-Z, 8-1/4" (210 mm) on the 2736-20, in their makers' figures.
Milwaukee Tool 2736-20
The Milwaukee Tool 2736-20 is Milwaukee Tool's M18 FUEL 8-1/4" Table Saw w/ One-Key, listed with a 8-1/4" (210 mm) blade. Each figure below comes from Milwaukee Tool's own pages, with a link to where it appears.
See it at Milwaukee ToolWhat a jobsite table saw is for. On jobsite saws, WEN Products writes: "these are the smallest, usually least-expensive saws, and often have blade diameters of 8" to 8-1/2", though many 10" models exist."
2736-20 specifications published by Milwaukee Tool (10)
- Blade diameter
- 8-1/4" (210 mm)2736-20 Operator's Manual (58-14-0089)
- Depth of cut
- 2-1/2"M18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool
- Bevel capacity
- 47 DegreesM18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool
- Miter capacity
- 60° Right or Left2736-20 Operator's Manual (58-14-0089)
- Dust port
- dust chute connects to a vacuum hose (diameter 2.5"/62.6 mm)Milwaukee Tool 2736-20 owner's manual
- Included
- Anti Kick Back Pawls (tool-only listing: In The Box (1))M18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool
- Warranty
- 5 Year Limited WarrantyM18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool
As published by Milwaukee Tool, read on 2026-09-28. Makers revise their tools; check Milwaukee Tool's current specification and manual before you buy.
The 2736-20 manual
Milwaukee Tool publishes Milwaukee Tool's owner's manual for the 2736-20 (PDF) and the parts list or diagram (PDF) on its own site. Read it before you buy as well as after: it is where Milwaukee Tool states the 2736-20 requirements in full.
From the 2736-20 manual and Milwaukee Tool's product page (3)
- Dado blades
- designed for use with a 6" stack dado (up to width of 3/4"); do not use an adjustable dado or molding cuttersMilwaukee Tool 2736-20 owner's manual
- Dado blades
- An optional dado throat plate is required for this procedureMilwaukee Tool 2736-20 owner's manual
- blade kerf limits
- Blade Kerf >1.8 mm minimum, <2.2 mm maximum; Blade body thickness <1.55 mm maximum; Riving knife thickness 1.6 mm (0.063")Milwaukee Tool 2736-20 owner's manual
Each row is our short reading of a passage on Milwaukee Tool's pages, linked to where it appears.
Before you buy the 2736-20
- Power supply. Milwaukee Tool lists 18V for the 2736-20. The manual says what circuit the 2736-20 needs.
- Dust port. Milwaukee Tool lists dust chute connects to a vacuum hose (diameter 2.5"/62.6 mm); match it to your extractor or collector's hose.
Guides that cover jobsite table saws
- Cordless vs corded woodworking tools: the makers' figures side by side
- Jobsite, contractor, hybrid or cabinet table saw: what the makers' specs show
- Track saw vs table saw for sheet goods: cut depth, rail length and rip capacity
- Miter saw vs table saw: what each maker says the tool is for
- How many amps does a table saw draw? The makers' own figures
Questions that include the 2736-20
Compare the 2736-20 with
2736-20 vs PBLTS01K
The 2736-20 beside the RYOBI PBLTS01K, row by row. Both are jobsite table saws with the same blade diameter: blade diameter 8-1/4" (210 mm) on the 2736-20, 8-1/4" on the PBLTS01K, in their makers' figures.
You may also consider
FLEX FX7211-Z
FLEX · jobsite table saw · blade diameter 8-1/4 in · rip capacity 25 in
Bosch GTS15-10
Bosch · jobsite table saw · blade diameter 10 in · current (amps) 15 · rip capacity Right: 32.125 in; Left: 14.125 in
SKIL SPT99-11
SKIL · jobsite table saw · blade diameter 10 IN. · current (amps) 15 Amp
Other jobsite table saws
SKIL TS6307-00
SKIL · jobsite table saw · blade diameter 10 IN. · current (amps) 15 Amps
Bosch GTS18V-08N14
Bosch · jobsite table saw
DEWALT DWE7485
DEWALT · jobsite table saw · rip capacity 24.5-in Of rip capacity
DEWALT DWE7491RS
DEWALT · jobsite table saw · blade diameter 10" · rip capacity 32-1/2 in.
DEWALT DWE7491X
DEWALT · jobsite table saw · rip capacity 32-1/2-in Rip capacity
RYOBI PBLTS01K
RYOBI · jobsite table saw · blade diameter 8-1/4" · rip capacity 12"
2736-20: questions answered from Milwaukee Tool's specification
What voltage does the Milwaukee Tool 2736-20 run on?
Milwaukee Tool lists the 2736-20 at 18V. Milwaukee Tool's manual gives the supply the 2736-20 needs.
Source: M18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool
What blade size does the Milwaukee Tool 2736-20 take?
The Milwaukee Tool 2736-20 takes a 8-1/4" (210 mm) blade, by Milwaukee Tool's specification.
How deep does the Milwaukee Tool 2736-20 cut?
Milwaukee Tool lists the depth of cut of the 2736-20 as 2-1/2".
Source: M18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool
What size is the dust port on the Milwaukee Tool 2736-20?
Milwaukee Tool lists the dust port on the 2736-20 as dust chute connects to a vacuum hose (diameter 2.5"/62.6 mm).
How much does the Milwaukee Tool 2736-20 weigh?
The Milwaukee Tool 2736-20 weighs 41.6 lb, by Milwaukee Tool's figure.
Source: M18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool
What warranty does Milwaukee Tool give on the 2736-20?
Milwaukee Tool lists the warranty on the 2736-20 as: 5 Year Limited Warranty.
Source: M18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool
What arbor size is the Milwaukee Tool 2736-20?
Milwaukee Tool lists the arbor of the 2736-20 as 5/8".
Source: M18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool
What comes with the Milwaukee Tool 2736-20?
Milwaukee Tool lists included for the 2736-20 as: Anti Kick Back Pawls (tool-only listing: In The Box (1)).
Source: M18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool
Where is the manual for the Milwaukee Tool 2736-20?
Milwaukee Tool publishes the 2736-20 manual on its own site; the link is under "The manual" on this page.
What does Milwaukee Tool say about dado blades on the 2736-20?
Per Milwaukee Tool's own pages for the 2736-20: designed for use with a 6" stack dado (up to width of 3/4"); do not use an adjustable dado or molding cutters. An optional dado throat plate is required for this procedure.
What does Milwaukee Tool say about blade kerf limits on the 2736-20?
Per Milwaukee Tool's own pages for the 2736-20: Blade Kerf >1.8 mm minimum, <2.2 mm maximum; Blade body thickness <1.55 mm maximum; Riving knife thickness 1.6 mm (0.063").
Sources
- M18 FUEL 8-1/4" Table Saw w/ One-Key | Milwaukee Tool — Milwaukee Tool
- 2736-20 Operator's Manual (58-14-0089) — Milwaukee Tool
- Milwaukee Tool 2736-20 owner's manual — Milwaukee Tool